See TALKING ELECTRONICS WEBSITE [632088]

See TALKING ELECTRONICS WEBSITE

email Colin Mitchell: [anonimizat]

INTRODUCTION
This e-book contains 100 transistor circuits. The se cond part of this e-book will contain a further 100
circuits.
Most of them can be made with components from your "junk box" and hopefully you can put them
together in less than an hour. The idea of this book is to get you into the fun of putting things together and there's nothing more
rewarding than seeing something work. It's amazing what you can do with a few transistors and some connecting components. And this is the
place to start. Most of the circuits are "stand-alone" and prod uce a result with as li ttle as 5 components.
We have even provided a simple way to produce your own speaker transformer by winding turns on a piece of ferrite rod. Many components can be obtained from transistor radios, toys and other pieces of
discarded equipment you will fi nd all over the place.
To save space we have not provided lengthy explanat ions of how the circuits work. This has already been
covered in TALKING ELECTRONICS Basic Electronics Course, and can be obtained on a CD for $10.00
(posted to anywhere in the world) See Talk ing Electronics website for more details:
http://www.talkingelectronics.com
Transistor data is at the back of this book and a transistor tester circuit is also provided. There are lots
of categories and I am sure many of the circuits wi ll be new to you, because some of them have been
designed recently by me. Basically there are two types of transistor: PNP and NPN. All you have to do is identify the leads of an unknown device and you can build almost anything.
You have a choice of building a circuit "in the ai r," or using an experimenter board (solderless
breadboard) or a matrix board or even a homemade pr inted circuit board. The choice is up to you but
the idea is to keep the cost to a minimu m – so don't buy anything expensive.
If you take parts from old equipment it will be best to solder them together "in the air" (as they will not
be suitable for placing on a solderless breadboard as the leads will be bent and very short).
This way they can be re-used again and again. No matter what you do, I know you will be keen to hear some of the "noisy" circuits in operation.
Before you start, the home-made Speaker Transformer project and Transistor Tester are the first things
you should look at.
If you are starting in electronics, see the World's Simplest Circuit. It shows how a transistor works and
three transistors in the 6 Million Gain project will detect microscopic levels of static electricity! You can
look through the Index but the names of the projects don't give you a full descri ption of what they do.
You need to look at everything. And I am sure you will.

KIT OF PARTS
Talking Electronics supplies a kit of parts that can be used to build the majority of the circuits in this book.
The kit costs $15.00 plus postage.

In many cases, a resistor or capacitor not in the ki t, can be created by putting two resistors or capacitors in
series or parallel or the next higher or lower value can be used. Don't think transistor technology is obsolete. Many co mplex circuits have one or more transistors to act as
buffers, amplifiers or to connect one block to another. It is absolutely essential to understand this area of
electronics if you want to carry out design-work or build a simple circuit to carry out a task.

CONTENTS

Ammeter 0-1A
Automatic Garden Light
Automatic Light
Bench Power Supply
Boom Gate Lights
Boxes
Buck Converter for LEDs 48mA
Buck Converter for LEDs 170mA
Buck Converter for LEDs 210mA
Cable Tracer
Clock – Make Time Fly
Colpitts Oscillator
Constant Current Source
Dancing Flower
Door-Knob Alarm
Dynamic Microphone Amplifier
Electronic Drums
Fog Horn
FRED Photopopper
Gold Detector
Guitar Fuzz
Hartley Oscillator
Heads or Tails
Hearing Aid Constant Volume
Hearing Aid Push-Pull Output
Hearing Aid 1.5v Supply
Hee Haw Siren
IC Radio
LED Detects Light
LED Flasher 1-Transistor
LED Torch with Adj Brightness
LED Torch with 1.5v Supply
Lie Detector
Light Alarm-1
Light Alarm-2
Light Alarm-3
Light Extender for Cars
Listener – phone amplifier
Make Time Fly!
Making 0-1A Ammeter
Metal Detector
Microphone Pre-amplifier
Motor Speed Controller
Movement Detector
Multimeter – Voltage of Bench Supply
Music to Colour
On-Off via push Buttons
Phaser Gun
Phone Alert
Phone Tape-1
Phone Tape-2
Phone Transmitter-1
Phone Transmitter-2
Phase-shift Oscillator Resistor Colour Code

Robo Roller
Robot
Robot Man – Multivibrator
Schmitt Trigger
SCR with Transistors
Second Simplest Circuit
Signal by-pass
Signal Injector
Simple Logic Probe
Siren
Solar Engine
Solar Engine Type-3
Solar Photovore
Sound to Light
Sound Triggered LED
Speaker Transformer
Spy Amplifier
Strength Tester
Sun Eater-1
Sun Eater-1A
Super Ear
Ticking Bomb
Touch Switch
Train Throttle
Transistor Pinouts
Transistor Tester-1
Transistor Tester-2
Trickle Charger 12v
Walkie Talkie
Walkie Talkie with LM386
Walkie Talkie – 5 Tr – circuit 1
Walkie Talkie – 5 Tr – circuit 2
Worlds Simplest Circuit
White LED Flasher
White LED with Adj Brightness
White Line Follower
Zener Diode (making)
0-1A Ammeter
1.5v to 9v Inverter
5 LED Chaser
5 Transistor Radio
6 Million Gain
6 to 12 watt Fluoro Inverter
12v Relay on 6v
12v Trickle Charger
20watt Fluoro Inverter
27MHz Door Phone
27MHz Transmitter
27MHz Transmitter – no Xtal
27MHz Transmitter-Sq Wave
27MHz Transmitter-2 Ch
27MHz Receiver
27MHz Receiver-2
303MHz Transmitter

RESISTOR COLOUR CODE
See resistors from 0.22ohm to 22M in full colour at end of book and another resistor table

A two-worm reduction gearbox producing a reduction
of 12:1 and 12:1 = 144:1 The gears are in the correct positions to produce the reduction.
BOXES FOR PROJECTS
One of the most difficult things to find is a box for a project.
Look in your local "junk" shop, $2.00 shop, fishing shop,
and toy shop. And in the medical section, for handy boxes. It's surprising where you will find an ideal box.
The photo shows a suitable box for a Logic Probe or other
design. It is a toothbrush box. The egg shaped box holds "Tic Tac" mouth sweeteners and the two worm reduction
twists a "Chuppa Chub." It cost less than $4.00 and the
equivalent reduction in a hobby shop costs up to $16.00!

to Index

The speaker t
is made by winding 50 turns
0.25mm wire on a small lengt
of 10mm dia ferrite rod.
The size and length of does not matter – it is just the
number of turns that makes
the transformer work. This is
called the secondary winding.
The primary winding is made by winding 300 turns of 0.01mm wire
(this is very fine wire) over the secondary and ending with a loop of
wire we call the centre tap.
Wind another 300 turns and this completes the transformer.
It does not matter which end of the secondary is connected to the top
of the speaker.
It does not matter which end of the primary is connected to the collector of the transistor in the circuits in this book.
ransformer
of
h
the rod
to Index

sensitive 3-transistor
er
SUPER EAR
This circuit is a very
amplifier using a speak
transformer. This can be
wound on a short length of
ferrite rod as show above or 150 turns on a 10mH
choke. The biasing of the
middle transistor is set for
3v supply. The second and
third transistors are not
turned on during idle conditions and the
quiescent current is just
5mA. The project is ideal for
listening to conversations
or TV etc in another room with long leads connecting
the microphone to the
amplifier.

TRANSISTOR
TESTER-1 CIRCUIT

The
10mH choke with 150 turns for the secondary
TRANSISTOR TESTER – 1
Transistor Tester – 1 project will test all types of
transistors including Darlington and power. The
circuit is set to test NPN types. To test PNP
types, connect the 9v battery around the other way at points A and B.
The transformer in the photo is a 10mH choke
with 150 turns of 0.01mm wire wound over the 10mH winding. The two original pins (with the red
and black leads) go to the primary winding and
the fine wires are called the Sec.
Connect the transformer either way in the circuit
and if it does not work, reverse either the primary
ot both).
r will work and any
speaker wilIf you use t in
the Home Ma
use one-side of the primary.

or secondary (but nAlmost any transforme
l be suitable.
he speaker transformer described
de Speaker Transformer article,
to Index
TRANSISTOR TESTER – 2
Here is another transistor tester.
This is basically a high gain amplifier
with feedbflash at ack that causes the LED to
a rate determined by the 10u
and 330k resistor.
Remove one of the transistors and
insert the unknown transistor. When it is
NPN with the pins as shown in the photo, the LED will flash. To turn the
unit off, remove one of the transistors.

to Index

WORLDS SIMPLEST CIRCUIT
This is the simplest circuit you can get. Any NPN transistor can be
used.

Connect the LED, 220 ohm resistor and transistor as shown in the
photo.
Touch the top point with two fingers of one hand and the lower point
with fingers of the other hand and squeeze.
The LED will turn on brighter when you squeeze harder.
Your body has resistance and when a voltage is present, current will
flow though your body (fingers). T he transistor is amplifying the current
through your fingers about 200 times and this is enough to illuminate
the LED.

to Index
SECOND SIMPLEST CIRCUIT

This the second simplest circuit in the world. A second
transistor has been added in place of your fingers. This
transistor has a gain of about 200 and when you touch the points shown on the diagram, the LED will illuminate with the
slightest touch. The transist or has amplified the current
(through your fingers) about 200 times.

to Index

6 MILLION GAIN!
This circuit is so sensitive it
will detect "mains hum."
Simply move it across any
wall and it will detect where the mains cable is located. It
has a gain of about 200 x
200 x 200 = 6,000,000 and will also detect static
electricity and the presence
of your hand without any
direct contact. You will be
amazed what it detects!
There is static electricity
EVERYWHERE! The input
of this circuit is classified as very high impedance.

to Index

The circuit uses a flashing LED to flash a super-bright
20,000mcd white LED
LED FLASHER WITH ONE TRANSISTOR!
This is a novel flasher circuit using a sing le driver transistor that takes its flash-
rate from a flashing LED. Tflasher in the photo is 3mm.
An ordinary LED will not work.
The flash rate cannot be
altered by the brightness of the high-bright white LED c
be adjusted by altering the 1
resistor across the 100u
electrolytic to 4k7 or 10k.
The 1k
the 100u so that when the
transistor turns on, the
charging current into the100u illuminates the white
LED.
If a 10k
used, the 100u is not fully discharged and the LED does not flash as bright.
All the parts in the photo are inmake it easy to see how the parts are connected.
he

an
k
resistor discharges

discharge resistor is

the same places as in the circuit diagram to
to Index

DANCING FLOWER
This circuit was taken from a
dancing flower.
A motor at the base of the
flower had a shaft up the stem and when the microphone
detected music, the bent shaft
made the flower wiggle and move.
The circuit will respond to a
whistle, music or noise.

to Index
WHITE LINE FOLLOWER
This circuit can be used for a toy car to follow a white line. The motor is
either a 3v type with gearing to steer
the car or a rotary actuator or a servo motor.
When equal light is detected by the
photo resistors the voltage on the base of the first transistor will be mid
rail and the circuit is adjusted via the
2k2 pot so the motor does not
receive any voltage. When one of the
LDR's receives more (or less) light,
the motor is activated. And the same thing happens when the other LDR
receives less or more light.

to Index
LED DETECTS LIGHT
All LEDs give off light of a particular colour but some LEDs are also
able to detect light. Obviously they are not as good as a device that has been specially made to detect light; such as solar cell, photocell,
photo resistor, light dependent resist or, photo transistor, photo diode
and other photo sensitive devices.
A green LED will detect light and a high-bright red LED will respond
about 100 times better than a green LED, but the LED in this position
in the circuit is classified as very high impedance and it requires a considerable amount of amplification to turn the detection into a
worthwhile current-source.
All other LEDs respond very poorly and are not worth trying.
The accompanying circuit amplifies the output of the LED and enables
it to be used for a number of applications.
The LED only responds when the light enters the end of the LED and this makes it ideal for solar trackers and any time there is a large
difference between the dark and light conditions. It will not detect the
light in a room unless the lamp is very close.

to Inde x

12v RELAY ON 6V SUPPLY
This circuit allows a 12v relay to operate on
a 6v or 9v supply. Most 12v relays need
about 12v to "pull-in" but will "hold" on
about 6v. The 220u charges via the 2k2 and bottom diode. When an input above
1.5v is applied to the input of the circuit,
both transistors are turned ON and the 5v across the electrolytic causes the negative
end of the electro to go below the 0v rail by
about 4.5v and this puts about 10v across
the relay.

to Index

MAKE TIME FLY!
Connect this circuit to an old electronic clock mechanism
and speed up the motor 100 times!
The "motor" is a simple "stepper-motor" that performs a
half-rotation each time the el ectromagnet is energised. It
normally takes 2 seconds for one revolution. But our circuit
is connected directly to the winding and the frequency can
be adjusted via the pot. Take the mechanism apart, remove the 32kHz crystal and
cut one track to the electromagnet. Connect the circuit
below via wires and re-assemble the clock.
As you adjust the pot, the "seconds hand" will move
clockwise or anticlockwise and you can watch the hours
"fly by" or make "time go backwards."
The multivibrator section needs strong buffering to drive
the 2,800 ohm inductive winding of the motor and that's why push-pull outputs have been us ed. The flip-flop circuit
cannot drive the highly inductiv e load directly (it upsets the
waveform enormously). From a 6v supply, the motor only gets about 4v due to the
voltage drops across the tr ansistors. Consumption is
about 5mA.
HOW THE MOTOR WORKS
The rotor is a magnet with the north pole shown with the red mark and the south pole opposite.
The electromagnet actually produces poles. A strong
North near the end of the electromagnet, and a weak North at the bottom. A strong South at the top left and
weak South at bottom left. The rotor rests with its poles
being attracted to the 4 pole-pieces equally.
Voltage must be applied to the electromagnet around the
correct way so that repulsion
occurs. Since the rotor is sitting equally between the North
poles, for example, it will see a
strong pushing force from the pole near the electromagnet
and this is how the motor
direction is determined. A reversal of voltage will revolve
the rotor in the same direction
as before. The design of the
motor is much more complex than you think!!

The crystal removed and a "cut track" to the coil. The 6 gears must be re-fitted for the hands to work.
A close-up of the clock motor
Another clock motor is shown below. Note the pole
faces spiral closer to the rotor to make it revolve in one direction. What a clever design!!

to Index
CONSTANT CURRENT SOURCE
This circuit provides a constant cu rrent to the LED. The LED can be
replaced by any other component and the current through it will depend on
the value of R2. Suppose R2 is 560R. When 1mA flows through R2, 0.56v will develop across this resistor and begin to turn on the BC547.
This will rob the base of BD 679 with turn-on voltage and the transistor
turns off slightly. If the supply voltage increases, this will try to increase the current through the circuit. If the cu rrent tries to increase, the voltage
across R2 increases and the BD 679 turns off more and the additional voltage appears across the BD 679. If R2 is 56R, the current through the circuit will be 10mA. If R2 is 5R6, the
current through the circuit will be 100mA – although you cannot pass
100mA through a LED without damaging it.

to Index
ON – OFF VIA MOME NTARY PUSH-BUTTONS
This circuit will supply current to the load R L. The maximum current will
depend on the second transistor. The circuit is turned on via the "ON" push
button and this action puts a current through the load and thus a voltage
develops across the load. This voltage is passed to the PNP transistor and it turns ON. The collector of the PNP keeps the power transistor ON.
To turn the circuit OFF, the "OFF" button is pressed momentarily. The 1k
between base and emitter of the power tran sistor prevents the base floating or
receiving any slight current from the PN P transistor that would keep the circuit
latched ON. The circuit was originally designed by a Professor of Engineering at Penn
State University. It had 4 mistakes. So much for testing a circuit!!!! It has been
corrected in the circuit on the left.

to Index
SIREN
This circuit produces a wailing or siren sound that gradually increases
and decreases in frequency as the
100u charges and discharges when
the push-button is pressed and
released. In other words, the circuit is not automatic. You need to press
the button and release it to produce
the up/down sound.

to Index
TICKING BOMB
This circuit produces a sound similar to a loud clicking clock. The frequency of the tick is adjusted by the 220k pot.
The circuit starts by charging the 2u2 and when 0.65v is on the base of
the NPN transistor, it starts to tu rn on. This turns on the BC 557 and
the voltage on the collector rises. This pushes the small charge on the 2u2 into the base of the BC547 to turn it on more.
This continues when the negative end of the 2u2 is above 0.65v and
now the electro starts to charge in the opposite direction until both
transistors are fully turned on. The BC 547 receives less current into
the base and it starts to turn off. Both transistors turn off very quickly
and the cycle starts again.

to Index
LIE DETECTOR
This circuit detects the resist ance between your fingers to pr oduce an oscillation. The detection-
points will detect resistances as high as 300k a nd as the resistance decreases, the frequency
increases.
Separate the two touch pads and attach them to the back of each hand. As the subject feels
nervous, he will sweat and change the frequency of the circuit.
The photos show the circuit built on PC boards with separate touch pads.
to Index

TOUCH SWITCH
This circuit detects the skin resistance of a finger to deliver a very small current to the super-alpha pair
of transistors to turn the circuit ON. The output of the "super transistor" turns on the BC 557 transistor.
The voltage on the top of the globe is passed to the front of the circuit via the 4M7 to take the place of
your finger and the circuit remains ON. To turn the circuit OFF, a finger on the OFF pads w ill activate the first transistor and this will rob the
"super transistor" of voltage and the circuit will turn OFF.

to Index
SIGNAL INJECTOR
This circuit is rich in harmonics and is ideal for testing amplifier circuits. To find a fault in an amplifier,
connect the earth clip to the 0v rail and move through
each stage, starting at the speaker. An increase in volume should be heard at each preceding stage.
This Injects will also go through the IF stages of
radios and FM sound sections in TV's.

to Index

LIGHT ALARM – 1
This circuit operates when the Light Dependent Resistor receives light.
When no light falls on the LDR, its resistance is high and the transistor
driving the speaker is not turned on.
When light falls on the LDR its resistance decreases and the collector of the second transistor falls. This turns o ff the first transistor slightly via the
second 100n and the first 100n puts an additional spike into the base of the second transistor. This continues until the second transistor is turned on as hard as it can go. The first 100n is now nearly charged and it
cannot keep the second transistor turned on. The second transistor starts
to turn off and both transistors swap conditions to produce the second
half of the cycle.

to Index
LIGHT ALARM – 2
This circuit is similar to Light Alarm -1 but produces a
louder output due to the speaker being connected
directly to the circuit.
The circuit is basically a high-gain amplifier that is turned on initially by the LDR and then the 10n
keeps the circuit turning on until it can turn on no
more. The circuit then starts to turn off and eventually turns
off completely. The current through the LDR starts
the cycle again.

to Index
LIGHT ALARM – 3 (MOVEMENT DETECTOR)
This circuit is very sensitive and can be plac ed in a room to detect the movement of a
person up to 2 metres from the unit.
The circuit is basically a high-gain amplifier (m ade up of the first three transistors) that
is turned on by the LDR or photo Darlington transistor. The third transistor charges the 100u via a diode and this delivers turn-on volt age for the oscillator. The LDR has equal
sensitivity to the photo tr ansistor in this circuit.

to Index

SOUND TRIGGERED LED
This circuit turns on a LED when the
microphone detects a loud sound.
The "charge-pump" section consists of
the 100n, 10k, signal diode and 10u electrolytic. A signal on the collector of
the first transistor is passed to the 10u
via the diode and this turns on the second transistor, to illuminate the
LED.

to Index
SIMPLE LOGIC PROBE
This circuit consumes no current when the probe is not touching any circuitry. The reason is the voltage across the
green LED, the base-emitter junction of the BC557, plus the
voltage across the red LED and base-emitter junction of the BC547 is approx: 2.1v + 0.6v + 1.7v + 0.6v = 5v and this is
greater than the supply voltage.
When the circuit detects a LOW, the BC557 is turned on and the green LED illuminates. When a HIGH (above 2.3v) is
detected, the red LED is illuminated.

to Index
TRAIN THROTTLE
This circuit is for model train enthusiasts.
By adding this circuit to your speed controller box, you will be able to simulate
a train starting slowly from rest.
Remove the wire-wound rheostat and replace it with a 1k pot. This controls the
base of the BC547 and the 2N3055
output is controlled by the BC547. The
diodes protect the transistors from
reverse polarity from the input and spikes
from the rails.

to Index
GUITAR FUZZ
The output of a guitar is connected to
the input of the Fuzz circuit. The output of this circuit is connected to
the input of your amplifier.
With the guitar at full volume, this circuit is overdriven and distorts. The
distorted signal is then clipped by the
diodes and your power amp amplifies the Fuzz effect.

to Index

STRENGTH TESTER
This is a simple "staircase" circuit in
which the LEDs come on as the
resistance between the probes
decreases. When the voltage on the base of
the first transistor sees 0.6v + 0.6v
+ 0.6v = 1.8v, LED1 comes on. LEDs 1&2 will come on when the
voltage rises a further 0.6v. The
amount of pressure needed on the
probes to produce a result, depends
on the setting of the 200k pot.

to Index
FOG HORN
When the push-button is pressed, the
100u will take time to charge and this
will provide the rising pitch and volume.
When the push-button is released, the level and pitch will die away. This is the
characteristic sound of a ship's fog
horn.

to Index
HEADS OR TAILS
When the push-button is pressed, the circuit will
oscillate at a high rate and both LEDs will
illuminate. When the push button is released, one
of the LEDs will remain illuminated. The 50k is
designed to equalise the slightly different values on each half of the circuit and prevent a "bias."

to Index
ROBOT MAN
This multivibrator circuit will
flash the Robot Man's eyes
as shown in the photo. The
kit of components is available from Talking
Electronics for $8.50 plus
postage. Send an email to
find out the cost of postage:
talking@tpg.com.au

to Inde x

DYNAMIC MICROPHONE
AMPLIFIER
This circuit takes the place of an
electret microphone. It turns an
ordinary mini speaker into a very
sensitive microphone. Any NPN transistors such as BC 547
can be used. The circuit will work from
3v to 9v. It is a common-base amplifier and accepts the low
impedance of the speaker to produce
a gain of more than 100.

to Index

SCR WITH TRANSISTORS
The SCR in circuit A produces a 'LATCH. ' When the button is pressed, the LED
remains illuminated.
The SCR can be replaced with two transistors as shown in circuit B.
To turn off circuit A, the current through the SCR is reduced to zero by the action of the OFF button. In circuit B the O FF button removes the voltage on the base
of the BC547. The OFF button could be placed across the two transistors and the circuit will turn off.

to Index
HEE HAW SIREN
The circuit consists of two multivibrators. The first multi-vibrator operates at a low
frequency and this provides the speed of t he change from Hee to Haw. It modifies
the voltage to the tone multivibrator, by firstly allowing full voltage to appear at the
bottom of the 220R and then a slightly lo wer voltage when the LED is illuminated.
to Index

MICROPHONE
PRE-AMPLIFIER
This circuit consists of
two directly coupled
transistors operating
as common-emitter amplifiers.
The ratio of the 10k
resistor to the 100R sets the gain of the
circuit at 100.

to Index
HARTLEY OSCILLATOR
The Hartley Oscillator is
characterised by an LC circuit in its
collector. The base of the transistor is
held steady and a small amount of signal is taken from a tapping on the
inductor and fed to the emitter to
keep the transistor in oscillation. The transformer can be any speaker
transformer with centre-tapped
primary.
The frequency is adjusted by
changing the 470p.

to Index
COLPITTS OSCILLATOR
The Colpitts Oscillator is
characterised by tapping the mid-point of the capacitive side of the
oscillator section. The inductor
can be the primary side of a
speaker transformer. The
feedback comes via the inductor.

to Index
PHASESHIFT OSCILLATOR
The Phaseshift Oscillator is characterised by 3
high-pass filters, creating a 180° phase shift.
The output is a sinewave. Take care not to
load the output – this will prevent reliable start-up and may stop the circuit from oscillating.
Reduced the 3k3 load resistor if the load
prevents the circuit oscillating.

to Index

DOOR-KNOB ALARM
This circuit can be used to detect when
someone touches the handle of a
door. A loop of bare wire is connected
to the point "touch plate" and the project is hung on the door-knob.
Anyone touching the metal door-knob
will kill the pulses going to the second transistor and it will turn off. This will
activate the "high-gain"
amplifier/oscillator.
The circuit will also work as a "Touch
Plate" as it does not rely on main hum, as many other circuits do.

to Index

MOTOR SPEED CONTROLLER
Most simple motor speed controllers simply reduce the voltage to a motor by introducing a series
resistance. This reduces the motor's torque and if
the motor is stopped, it will not start again. This circuit detects the pulses of noise produced by
the motor to turn the circuit off slightly. If the motor
becomes loaded, the amplitude of the pulses decreases and the circuit turns on more to deliver a
higher current.

to Index
ELECTRONIC DRUMS
The circuit consists of two
"twin-T" oscillators set to a
point below oscillation.
Touching a Touch Pad will set the circuit into oscillation.
Different effects are produced
by touching the pads in different ways and a whole
range of effects are available.
The two 25k pots are adjusted
to a point just before oscillation.
A "drum roll" can be produced
by shifting a finger rapidly across adjacent ground and
drum pads.

to Index

LIGHT EXTENDER
This circuit is a Courtesy Light Extender for cars. It
extends the "ON" time when a door is closed in a
car, so the passenger can see where he/she is
sitting. When the door switch is opened, the light normally
goes off immediately, but the circuit takes over and
allows current to flow because the 22u is not charged and the first BC 547 transistor is not
turned ON. This turns on the second BC547 via the
100k and the BD679 is also turned on to illuminate
the interior light.
The 22u gradually charges via the 1M and the first BC547 turns on, robbing the second BC547 of
"turn-on" voltage and it starts to turn off the BD679.
The 1N4148 discharges the 22u when the door is opened.

to Index
20 WATT FLUORO INVERTER
This circuit will drive a 40 watt fluoro or two 20-
watt tubes in series.
The transformer is wound on a ferrite rod
10mm dia and 8cm long.
The wire diameters are not critical but our prototype used 0.61mm wire for the primary
and 0.28mm wire for the secondary and
feedback winding. Do not remove the tube when the circuit is
operating as the spikes produced by the
transformer will damage the transistor.
The circuit will take approx 1.5amp on 12v,
making it more efficient than running the tubes
from the mains. A normal fluoro takes 20 watts for the tube and about 15 watts for the ballast.

to Index
6 to 12 WATT FLUORO INVERTER
This circuit will drive a 40 watt fluoro or two 20-watt
tubes in series but with less brightness than the
circuit above and it will take less current. 2 x 20 watt tubes = 900mA to 1.2A and 1 x 20 watt
tube 450mA to 900mA depending on pot setting.
The transformer is wound on a ferrite rod 10mm dia and 8cm long. The wire diameter is fairly critical and
our prototype used 0.28mm wire for all the windings.
Do not remove the tube when the circuit is operating as the spikes produced by the transformer will
damage the transistor. The pot will adjust the
brightness and vary the current consumption. Adjust
the pot and select the base-bias resistor to get the
same current as our prot otype. Heat-sink must be
greater than 40sq cm. Use heat-sink compound.

to Index

GOLD DETECTOR
This very simple circuit will detect
gold or metal or coins at a
distance of approx 20cm –
depending on the size of the object.
The circuit oscillates at approx
140kHz and a harmonic of this frequency is detected by an AM
radio.
Simply tune the radio until a
squeal is detected.
When the search coil is placed
near a metal object, the
frequency of the circuit will
change and this will be heard from the speaker.
The layout of the circuit is shown
and the placement of the radio.

to Index

PHASER GUN
This is a very effective circuit. The sound is amazing. You have to build it to appreciate the
range of effects it produces. The 50k pot pr ovides the frequency of the sound while the
switch provides fast or slow speed.
to Index

IC RADIO
This circuit contains an IC but it looks like a 3-leaded transistor and that's why we have
included it here.
The IC is called a "Radio in a Chip" and it contains 10 transistors to produce a TRF (tuned Radio Frequency) front end for our project.
The 3-transistor amplifier is taken from our SUPER EAR project with the electret
microphone removed.
The two 1N 4148 diodes produce a constant voltage of 1.3v for the chip as it is designed for
a maximum of 1.5v. The "antenna coil" is 60t of 0.25mm wire wound on a 10mm ferrite rod. The tuning capacitor
can be any value up to 450p.

to Inde x

5-TRANSISTOR RADIO
If you are not able to get the ZN414 IC, this circuit uses two transistors to take the
place of the chip.

to Index
AUTOMATIC LIGHT
This circuit automatically turns on a light when illumina tion is removed from the LDR. It remains ON for the
delay period set by the 2M2 pot.
The important feature of this circuit is the building bloc ks it contains – a delay circuit and Schmitt Trigger. These
can be used when designing other circuits.
to Index
5-LED CHASER
The LEDs in this circuit produce a casing pattern similar the running LEDs
display in video shops.
All transistors will try to come on at the same time when the power is
applied, but some will be faster due to their internal characteristics and some will get a different turn-on current due to the exact value of the 22u electrolytics.
Only 3 of the LEDs will be on at any one-time as the display has to be ON-
OFF-ON-OFF-ON.
The circuit can be extended to any number of odd stages.

to Index
BENCH POWER SUPPLY

This power supply can be built in less than an hour on a piece of copper-laminate. The board acts
as a heat-sink and the other components can be moun ted as shown in the photo, by cutting strips
to suit their placement.
The components are connected with enamelled wire and the transistor is bolted to the board to
keep it cool. The Bench Power Supply was designed to use old "C," "D" and lantern batteries, that's why there are no diodes or electrolytics. Collect all your old batteries and cells and connect them together to
get at least 12v -14v. The output of this power supply is regulated by a 10v zener made up of the characteristic zener
voltage of 8.2v between the base-emitter leads of a BC547 transistor (in reverse bias) and approx
1.7v across a red LED. The circuit will deliver 0v – 9v at 500mA (depending on the life left in the
cells your are using). The 10k pot adjusts the output voltage and the LED indicates the circuit is ON.
It's a very good circuit to get the last of the energy from old cells.

to Index
ADDING A VOLT-METER TO THE BENCH POWER SUPPLY

A voltmeter can be added to the Bench Po wer Supply by using a very low cost
multimeter. For less than $10.00 you can get a mini multimeter with 14 ranges, including
a 10v range. The multimeter can also be used to monitor current by removing the
negative lead and making a new RED lead, fitting it to the "—" of the multimeter and

selecting the 500mA range as shown in the photo below:

to Index
MAKING 0-1Amp meter fo r the BENCH POWER SUPPLY

The item in the photo is called a
"Movement." A movement is a moving coil with a pointer and no resistors connected
to the leads.
Any Movement can be converted to an ammeter without any mathematics.
Simply solder two 1R resistors (in parallel)
across the terminals of any movement and connect it in series with an ammeter on th
output of the Bench Power Supply. The
second ammeter provides a reference so
you can calibrate the movement. Con
a globe and increase the voltage.
At 500mA, if the pointer is "up scale" (reading too high) add a trim-resistor. In
our case it was 4R7.
The three shunt resistors can be clearly seen in t he photo. Two 1R and the trim resistor is 4R7.
You can get a movement from an old multimeter or they are available in electronics shops as a separate
item. The sensitivity does not matter. It can be 20uA or 50uA FSD or any sensitivity.
e
nect
to Index

MAKING A ZENER DIODE
Sometimes a zener diode of the required voltage is not available. Here are a number of components
that produce a characteristic voltage across them. Si nce they all have different voltages, they can be
placed in series to produce the voltage you need. A re ference voltage as low as 0.65v is available and
you need at least 1 to 3mA through the device(s) to put them in a state of conduction (breakdown).

to Index
12v TRICKLE CHARGER

The 12v Trickle Charger circuit uses a TIP3055 power transistor to limit the current to the battery by
turning off when the battery voltage reaches approx 14v or if the current rises above 2 amp. The signal
to turn off this transistor comes from tw o other transistors – the BC557 and BC 547.
Firstly, the circuit turns on fully via the BD13 9 and TIP3055. The BC557 and BC 547 do not come into
operation at the moment. The current through the 0. 47R creates a voltage across it to charge the 22u
and this puts a voltage between the base and emitter of the BC547. The transistors turn on slightly and remove some of the turn-on voltage to the BD 139 and this turns off the TIP3055 slightly.
This is how the 2 amp max is created. As the battery voltage rises, the voltage divider made up of the 1k8 and 39k creates a 0.65v between
base and emitter of the BC557 and it starts to turn on at approx 14v. This turns on the BC 547 and it
robs the BD136 of "turn-on" voltage and the TIP3055 is nearly fully turned off.
All battery chargers in Australia must be earthed. The negative of the output is taken to the earth pin.

to Index

1.5v to 9v INVERTER

This very clever circuit will convert 1.5v to 9v to take the place of those expensive 9v
batteries.
But the clever part is the voltage regulating se ction. It reduces the current to less than
10mA when no current is being drawn from the output. You can use two or three old cells for the supply and the circuit will totally use up all the energy from the cells. It's a
great circuit for using up those old cells. With a 470R load, the output current is 20mA
and the voltage drop is less than 10mV. It is best to use 3 old cells as this will deliver
about 2.5v to 3v and the circuit will produce an efficiency of about 70%. Adjust the 15k
resistor for 9v.

to Index
27MHz TRANSMITTER
The transmitter is a very simple crystal oscillator. The heart of the circuit is the tuned circuit consisting of the primary of
the transformer and a 10p capacitor. The
frequency is adjusted by a ferrite slug in the centre of the coil until it is exactly the
same as the crystal. The transistor is
configured as a common emitter amplifier. It has a 390R on the emitter for
biasing purposes and prevents a high
current passing through the transistor as the resistance of the transformer is very
low.
The "pi" network matches the antenna to the output of the circuit. See full
description in 27MHz Links
article.
to Index

27MHz RECEIVER
The 27MHz receiver is really a transmitter. It's a ve ry weak transmitter and delivers a low level signal to
the surroundings via the antenna. When another signal (from the transmitter) comes in contact with the
transmission from the receiver it creates an interfer ence pattern that reflects down the antenna and into
the first stage of the receiver.
The receiver is a super-r egenerative design. It is self-oscillating (o r already oscillating) and makes it
very sensitive to nearby signals. See full description in 27MHz Links article.
to Index
27MHz TRANSMITTER WITHOUT A
CRYSTAL
A 27MHz transmitter without a crystal. When
a circuit does not have a crystal, the oscillator
is said to be "voltage dependent" or "voltage
controlled" and when the supply voltage drops, the frequency changes.
If the frequency drifts too much, the receiver
will not pick up the signal. For this reason, a simple circuit as shown is not recommended.
We have only included it as a concept to
show how the 27MHz frequency is generated.
It produces a tone and this is detected by a
receiver.

See full description in 27MHz Links article.
to Index

27MHz TRANSMITTER WITH SQUARE-WAVE OSCILLATOR
The circuit consists of two blocks. Block 1is a multivib rator and this has an equal mark/space ratio to turn
the RF stage on and off. Block 2 is an RF oscillator. T he feedback to keep the st age operating is provided
by the 27p capacitor. The frequency-producing items ar e the coil (made up of the full 7 turns) and the 47p
air trimmer. These two items are called a parallel tu ned circuit. They are also called a TANK CIRCUIT as
they store energy just like a TANK of water and pass it to the antenna. The frequency of the circuit is
adjusted by the 47p air trimmer. See full description in 27MHz Links article.
to Index

27MHz RECEIVER-2
This circuit matches with the 27MHz Transmitter wi th Square-wave Oscillator. See full description on
Talking Electronics website: 27MHz Links article.
to Index

WALKIE TALKIE
Nearly all the components in the 4-transistor circui t are used for both transmitting and receiving. This
makes it a very economical design. The frequency-generating stage only needs the crystal to be removed
and it becomes a receiver. Next is a three transistor directly coupled audio amplifier with very high gain.
The first transistor is a pre-amplifier and the next tw o are wired as a super-alpha pair, commonly called a
Darlington pair to drive the speaker transformer. See full description in 27MHz Links article.
to Index
27MHz TRANSMITTER – 2 CHANNEL
This circuit does not use a crystal but has a
clever feature of using the two push buttons to
turn the circuit on when it is required to
transmit.
The frequency of the multivibrator is
determined by the value of resistance on the base of each transistor. The multivibrator is
driven directly from the supply with the forward
button and via a 150k for the reverse
frequency.
The receiver requires a 1kHz tone for forward
and 250Hz for reverse.

See full description in 27MHz Links article.
to Index

303MHz TRANSMITTER
The transmitter circuit is made up of
two building blocks – the 303MHz RF
oscillator and the 32kHz crystal
controlled oscillator to generate a tone so the receiver does not false-
trigger.
The 303MHz oscillator consists of a self-oscillating circuit made up of the
coil on the PC board and a 9p (9
puff) capacitor.

See full description in Wireless
Doorbell article.
to Index
Type: Gain: Vbe Vce Current Case
2SC1815 NPN 100 1v 50v 150mA
2SC3279 NPN 140 to
600
@0.5A 0.75v 10v 2amp

BC337
BC338 NPN 60
@300mA 0.7v 45v
25v 800mA

BC547
BC548
BC549 NPN 70
@100mA 0.7v 45v
30v
30v 100mA
BC557 PNP 45v 100mA

BD139 NPN 70-100
@150mA 0.5v 80v 1.5A
BD140 PNP 70-100
@150mA 0.5v 80v 1.5A

2SCxxx
8050 NPN 10v 1.5A
8550 PNP 10v 1.5A
9012 PNP 500mA
9013 NPN 1v 20v 500mA
9014 NPN 100mA
9015 PNP 100mA
9018 NPN 700MHz 15v 50mA

to Index

BOOM GATE LIGHTS
This simple circuit will
produce flashing lights for
your model railway crossing.
It uses one flashing LED and one normal red LED, with a
green LED hidden in the
background. It can be used somewhere else on your
layout but it is needed to
produce a voltage drop so
the two red LEDs will flash.
You cannot get a simpler circuit.

to Index

The 1/10th watt resistors used in this circuit,
compared with
0.25watt resistors.

5 TRANSISTOR WALKIE TALKIE – 1
This walkie talkie circuit does not have a crystal or speaker transformer, with the board measuring
just 3cm x 4cm and using 1/10th watt resistors, it is one of the smallest units on the market, for just
$9.50 to $12.00. The wires in the photo go to the battery, speaker, call-switch and antenna. The
most difficult component in the circuit to duplicat e is the oscillator coil. See the photo for the size
and shape. The coil dia is 5mm and uses 0.25mm wire. The actual full-turn or half turn on the coil is
also important. Almost all 5 transistor walkie talkie s use this circuit or slight variations. See the
article: 27MHz Transmitters for theory on how these transmitters work – it is fascinating.
to Index

5 TRANSISTOR WALKIE TALKIE – 2
Here is another walkie talkie circuit, using slightly different values for some of the
components. See the article: 27MHz Transmitters for theory on how these transmitters work.
to Index
WALKIE TALKIE with LM386
Here is a more up-to-date version of the walkie talkie, using an LM 386 amplifier
IC to take the place of 4 transistors.
to Index

SPY AMPLIFIER
This simple circuit will detect very faint sounds and deliver them to a 32 ohm earpiece.
The circuit is designed for 1.5v operation and is available from $2.00 shops for less than
$5.00 The photo shows the surface-mount components used in its construction.
to Index

HEARING AID 1.5v
SUPPLY
This simple circuit will
detect very faint sounds
and deliver them to an 8
ohm earpiece. The circuit is designed for 1.5v
operation.

to Index
HEARING AID with
PUSH PULL OUTPUT

This circuit will detect
very faint sounds and
deliver them to an 8 ohm earpiece. It is designed
for 3v operation.

to Index

HEARING AID with CONSTANT VOLUME
This is a very handy circuit as it provides co nstant volume. It is designed for 3v operation.
to Index

SOLAR ENGINE
This circuit is called Type-1 SE. Low current from a solar cell is stored in a
large capacitor and when a preset voltage-level is reached, the energy from
the capacitor is released to a motor.
For full details on how the circuit works and how to modify it, see:
http://www.talkingelectronics.c om/projects/Robots/Page2.html
to Index
SUN EATER-I
An improved design over Solar Engine circuit above. It has a clever 2-transistor self-latching arrangement to keep the circuit ON until the
voltage drops to 1.5v. The circuit turns on at 2.8v. This gives the motor
more energy from the electrolytic at each "pulse." For full details on how
the circuit works and how to modify it, see:

http://www.talkingelectronics.c om/projects/Robots/Page2.html
to Index

SUN EATER-1A
This circuit is an improvement on the Sun Eater I shown above. It works exactly the same except the slight re-
arrangement of the components allows an NPN power transistor to be used. One less resistor is needed and one
less capacitor but two extra diodes have been a dded to increase the upper turn-on voltage.
For full details on how the circuit works and how to modify it, see:
http://www.talkingelectronics.c om/projects/Robots/Page2.html
to Index

SOLAR ENGINE Type-3
Type-3 circuits are current controlled or current-
triggered. This is another very clever way of
detecting when the electrolytic has reached its
maximum charge.
At the beginning of the charge-cycle for an electrolytic, the charging current is a maximum. As
the electrolytic becomes c harged, the current drops.
In the type-3 circuit, the charging current passes
through a 100R resistor and creates a voltage drop. This voltage is detected by a transistor (Q2) and
the transistor is turned ON.
This action robs transistor (Q1) from turn-on voltage a nd the rest of the circuit is not activated. As the
charging current drops, Q2 is gradually turned off and Q1 becomes turned on via the 220k resistor
on the base.
This turns on Q3 and the motor is activated. T he voltage across the storage electrolytic drops and
the current through the 100R rises and turns the circuit off. The elec trolytic begins to charge again
and the cycle repeats. For full details on how t he circuit works and how to modify it, see:

http://www.talkingelectronics.c om/projects/Robots/Page2.html
to Index

SOLAR PHOTOVORE
The green LEDs cause the Solar Engine on the opposite side to fire and the Solar Photovore turns
toward the light source. The motors are two pager "v ibe" motors with the weights removed. The 100k
pot on the "head" balances the two Solar Engines. If you cannot get the circuit to work with green
LEDs, use photo-transistors. For full details on how the circuit works and how to modify it, see:
http://www.talkingelectronics.c om/projects/Robots/Page4.html
to Index
FRED Photopopper (Flashing LED )
It is a Photopopper using low-cost components. It uses tw o red or green flashing LEDs to turn the circuit on
when the voltage across the electrolytic has reache d about 2.7v. The flashing LEDs change characteristics
according to the level of the surrounding light and this turns the circuit into phototropic.
For full details on how the circuit works and how to modify it, see:
http://www.talkingelectronics.c om/projects/Robots/Page6.html
to Index

ROBO ROLLER
The circuit consists of two building blocks. The
Photopopper circuit and a voltage multiplying (or
voltage increasing) circuit from a Solar Charger
project.
For full details on how the circuit works and how to modify it, see:
http://www.talkingelectronics.c om/projects/Robots/Page7.html
to Index
SIGNAL BY-PASS
This circuit allows a class-A amplifier to drive a low
impedance speaker and has a low quiescent current. The
220R in series with the speaker limits the "wasted" cto about 20mA max as the transistor is generally biased
at mid-voltage. However t he transistor will be almost
directly driving the speaker when a signal is being
processed and the only limitati on is the ability of the 220R
to discharge the 100u during each cycle. The circuit is called a signal by-pass as the signal by-
passes the 220R and drives t he speaker directly (via the
100u).
urrent
to Index

SOUND-TO-LIGHT
The LED illuminates when the pi ezo diaphragm detects sound.
Some piezo diaphragms are very sensitive and produce 100mV when whistling at
50cm. Others produce 1mV. You must test them with a CRO.
The sensitivity of the diaphragm will deter mine the sensitivity of the circuit.
to Index

Above: A 3.5mm switched stereo plug and socket wiring.

MUSIC-TO-COLOUR
The LED illuminates when the circuit detects a high amplitude waveform. It
can be connected to a "Walkman" or mini radio with earphones. A second
channel can be connected to produce a stereo effect.
to Index

This is the professional unit The transmitter is built on a small length of PC board, cut into lands
with a file. The photo clearly shows how all the components are
mounted and how the board is fitted into a toothbrush holder. The flashing LED shows the unit is ON and serves to control the beep-
beep-beep of the circuit.

TRANSMITTER CIRCUIT

RECEIVER CIRCUIT The receiver circuit is a high-
gain amplifier and produces
constant background noise
so the slightest magnetic field can be detected.
The 10mH choke can be any
value but the largest number of turns on the core is best.
The mini speaker can be a
16R earpiece but these are
not as loud as a mini speaker.
Quiescent current is 50mA so
the on-off switch can be a
push-button.

CABLE TRACER
Why pay $100 for a cable tracer when you can build one fo r less than $10.00! This type of tracer is used by
telephone technicians, electricians and anyone laying, r eplacing or wiring anything, using long cables, such
as intercoms, television or security.
Our cable tracer consists of two units. One unit has a multivibrator with an output of 4v p-p at approx 5kHz.
This is called the transmitter. The other unit is a very sensitive amplifier with capacitive input for detecting the tone from the transmitter and a magnetic pickup for de tecting magnetic lines of force from power cables
carrying 240v. This is called the receiver. The circuit also has an inductive loop, made up of a length of wire,
to pick up stray signals from power cables, so if one detector does not detect the signal, the other will. Our
circuit is nothing like that in t he professional unit shown above.

to Index
LED TORCH with 1.5v SUPPLY
This simple circuit will illuminate a super-bright white LED to full brightness with 28mA from a
1.5v cell. The LED is 20,000mcd (20cd @ 15° viewing angle) and has an output of approx
1lumen.
The transformer is wound on a small ferrite slug 2.6mm dia and 6mm long. It is made from F29
ferrite material as the circuit operates at a high
frequency (100kHz to 500kHz).
The efficiency of the circuit revolves around the
fact that a LED will produ ce a very high output
when delivered pulses, but the overall current
will be less than a steady DC current.
BC 337 has a collector-emitter voltage of 45v. (BC338 has 25v collector-emitter voltage
rating.) The voltage across the transistor is no
more than 4v as the LED absorbs the spikes. Do not remove the LED as the spikes from the
transformer will damage the transistor.
The circuit will drive 1 or 2 while LEDs in series.

to Index

WHITE LED FLASHER
This circuit will flash a super-bright
white LED from a 1.5v cell.
The transformer is wound on a small
ferrite slug 2.6mm dia and 6mm long as shown in a project above.
The circuit uses the zener
characteristic of the reverse-base-emitter junction of a BC 547 to pass
current and flash the LED.

to Index
LED TORCH with ADJUSTABLE BRIGHTNESS
This circuit will drive up to 3 hi gh-bright white LEDs from a 3v
supply. The circuit has a pot to adjust the brightness to
provide optimum brightness for the current you wish to draw
from the battery. The transformer is wound on a ferrite slug 2.6mm dia and
6mm long as shown in the LED Torch with 1.5v Supply
project. This circuit is a "Boost Converte r" meaning the supply is less
than the voltage of the LEDs. If the supply is greater than the voltage across the LEDs, they will be damaged.

to Index

Inductor: 60 turns
on 10mm ferrite rod, 15mm long.
BUCK CONVERTER for HIGH-POWER LED
48mA to 90mA
This circuit is a "Buck Converter" meaning the supply is
greater than the voltage of the LED. It will drive 1 high-power white LED from a 12v supply and is capable of
delivering 48mA when R = 5R6 or 90mA when R = 2R2.
The LED is much brighter when using this circuit, compared with a series resistor delivering the same current.
But changing R from 5R6 to 2R2 does not double the
brightness. It only increases it a small amount. The inductor consists of 60 turns of 0.25mm wire, on a
15mm length of ferrite rod, 10mm diameter. Frequency of
operation: approx 1MHz.
The circuit is not designed to drive one 20mA LED.
This circuit draws the maximum for a BC 338.

to Index

BUCK CONVERTER for HIGH-POWER
LED 210mA
This circuit will drive 1 high-power white LED from
a 12v supply and is capable of delivering 210mA.
The driver transistor is BD 139 and the details of
the inductor are shown above. The voltage across the LED is approx 3.3v – 3.5v
The driver transistor w ill need a small heatsink.
The 2R2 can be increased if a lower drive-current
is required.

to Inde x
BUCK CONVERTER for HIGH-POWER
LED 170mA
This circuit is slightly simpler than above but it does
not have the feature of being able to adjust the
drive-current.
The inductor is the same as the photo above but has a feedback winding of 15 turns.
Connect the circuit via a 220R resistor and if the
LED does not illuminate, reverse the feedback winding.
The driver transistor w ill need a small heatsink.

to Index

AUTOMATIC GARDEN LIGHT
This circuit automatically turns on and illuminates the LEDs when the solar panel does not
detect any light. It switches off when the sola r panel produces more than 1v and charges the
battery when the panel produces more than 1.5v + 0.6v = 2.1v
to Index

27MHz DOOR PHONE
This circuit turns a walkie talkie into a handy
wireless door phone. It saves wiring and the
receiver can be taken with you upstairs or
outside, without loosing a call from a visitor. A 5-Transistor walkie talkie can be used (see
circuit
above) and the modifications made to
the transmitter and receiver are shown below: THE TRANSMITTER
Only three sections of the transmit/ receive
switch are used in the walkie talkie circuit and
our modification uses the fourth section. Cut the tracks to the lands of the unused section
so it can be used for our circuit.
There are a number of different printed circuit
boards on the market, all using the same
circuit and some will be physically different to
that shown in the photo. But one of the sections of the switch will be unused.
Build the 2-transistor delay circuit and c
it to the walkie talkie board as shown. Wthe "push-to-talk" switch is pressed, the PC
board will be activated as the delay circuit
effectively connects the negative lead of tbattery to the negative rail of the board for
about 30 seconds.
The 100u gradually discharges via the 1M after t he "press-to-talk" switch is released and the two
transistors turn off and the current drops to less t han 1 micro-amp – that's why the power switch can
be left on. .
The transmitter walkie talkie is placed at the front door and the power switch is turned on. To call,
push the "push-to-talk" switch and the "CALL" button at the same time for about 5 seconds. The
circuit will activate and when the "push-to-talk" sw itch is released, the circuit will produce background
noise for about 30 seconds and you will hear when call is answered.
The "push-to-talk" switch is then used to talk to the other end and this will activate the circuit for a
further 30 seconds. If the walkie talkie does not have a "CALL" switch, 3 components can be added to
provide feedback, as shown in the circuit below, to produce a tone.

THE RECEIVER
The receiver circuit needs modification and a 2-transi stor circuit is added. This circuit detects the tone
and activates the 3-transistor direct-coupled amp lifier so that the speaker produces a tone.
The receiver circuit is switched on and the 2-transist or circuit we connect to the PC board effectively
turns on the 3-transistor amplifier so that the qui escent current drops from 10mA to about 2-3mA. It
also mutes the speaker as the amplifier is not activated. The circuit remains on all the time so it will
be able to detect a "CALL." When a tone is picked up by the first two transistors in the walkie talkie, it
is passed to the first transistor in our "add-on" se ction and this transistor produces a signal with
sufficient amplitude to remove the charge on the 1u electrolytic. This switches off the second
transistor and this allows the 3-transistor amplifie r to pass the tone to the speaker. The operator then
slides a switch called "OPERATE" to ON (down) and this turns on the 3-transistor amplifier. Pressing
the "push-to-talk" switch (labelled T/R) allows a conversation with the per son at the door. Slide the
"OPERATE" switch up when finished. onnect
hen

he

The receiver walkie talkie wi th the 2-transistor "add-on"
to Index

SCHMITT TRIGGER
A Schmitt Trigger is any circuit that has a fast change-over from one
state to the other. In our case we have used 2 transistors to produce
this effect and the third is an emitter-follower buffer. The circuit will drive a LED or rela y and the purpose is to turn the LED
ON quickly at a particular level of illumination and OFF at a higher level. The gap between ON and OFF is called the HYSTERESIS GAP.
to Index

PHONE TAPE – 1
This simple circuit will allow you to tape-record a conversation from a phone line.
It must be placed between the plug on the wall and the phone.
The easiest way is to cut an extension lead. Wind 300-500 turns of 0.095mm wire on a
plastic straw and place the reed switch inside. Start with 300 turns and see if the reed switch activates, Keep adding turns until the switch is reliable.
Fit two 100n capacitors to the ends of the winding for the audio. Plug the Audio into
"Mic" on tape recorder. Plug the remote into "remote" on the tape recorder and push
"record." The tape recorder will turn on when the phone is lifted and record the
conversation.

to Index

PHONE TAPE – 2
The circuit is turned off when the phone line is 45v as the voltage divider made up of the 470k, 1M and 100k put s 3.5v on the base of the first
BC557 transistor. If you are not able to get to cut the lead to the phone,
the circuit above will record a conv ersation from an extension lead. The
remote plug must be wired around the correct way for the motor to
operate.

to Index

PHONE ALERT
Two circuits are available to show when a phone is being used. The first circuit must be placed
between the socket on the wall and the phone – such as cutting into the lead and insert the
bridge and diode.
But if you cannot cut the lead to the phone, you will have to add an extension cord and place the
second circuit at the end of the line. You can also connect a phone at the end if needed.
to Index
THE LISTENER
This circuit consists of a 4-transistor amplifier and a 3-transistor "switch" that detects when the phone line is
in use, and turns on the amplifier. The voltage di vider at the front end produces about 11v on the base of
the first BC557 and this keeps the transistor off. Switch the unit off when removed from the phone line.
to Index

PHONE TRANSMITTER – 1
The circuit will transmit a phone conversation to an FM radio on the 88-108MHz band. It uses energy from the
phone line to transmit about 100metres. It uses the phone wire as the antenna and is activated when the phone is
picked up. The components are mounted on a small PC board and the lower photo clearly shows the track-work.
to Index

PHONE TRANSMITTER – 2
The circuit will transmit a phone conversation to an FM radio on the 88-
108MHz band. It uses energy from the phone line to transmit about
200metres. It uses the phone wire as the antenna and is activated when the
phone is picked up.
to Index

ROBOT-1
A simple robot can be made with 2 motors and two light -detecting circuits, (identical to the circuit above).
The robot is attracted to light and when the light dependent resistor sees light it s resistance decreases.
This turns on the BC547 and also the BC557. The shaft of the motor has a rubber foot that contacts the
ground and moves the robot. The two pots adjust the sens itivity of the LDRs. This kit is available from
Velleman as kit number MK127.

All the resistor colours: